- #How to program a urc remote how to#
- #How to program a urc remote code#
- #How to program a urc remote tv#
If you are entering a single digit number, you must PRESS 0 first.ENTER the channel number of the channel would like to add to your favorite channel list.
#How to program a urc remote tv#
You can set up the FAV CH key with a list of up to 10 of your favorite channels on either your TV or your Cable Box/Satellite/DSS. Your One For All® 4 Device is equipped with a favorite channel key ( FAV CH ). If you hit the PLAY button - the VCR will PLAY, if you hit SETUP -PLAY it will bring up a display. To use the function: TAP the SETUP button and release, then TAP the key you chose.įOR EXAMPLE:VCR-SETUP(hold 2 blinks) 9-9-4 SETUP 2-3-4 SETUP PLAY In order to stack a second function on a key when pressing the button you want the function on in the sequence, instead hit SETUP and then the button you want. You would have to do the same process for VOL DN and MUTE. It would be: SETUP - 9 - 9 - 4 -TV - VOL UP - VCR- VOL UP - two blinks.
#How to program a urc remote code#
If the keypad continues to act "scrambled", you may:Ī wrong code may only operate a few functions of your equipment or they may be operating inaccurately. If your remote seems to be acting this way, try the following proceedure: Functions like channels, volume, or numbers are not where they should be. Sometimes it seems that the keypad is "scrambled". PRESS the button you want to clear twice.PRESS the button you want to clear - RELEASE.Now The volume is set for all original devices. PRESS the VOLUME+ key, you will get two blinks.Use this to get the original volume to work on each device. Other devices- refer to the instructions under "KEYMOVER-From one button to another" If you want to set the volume for a device to work just one or two NOTE: This only sets volume in the TV,VCR,CABLE, or SAT mode. PRESS the device key you would like the volume to come from.This sets Volume to work for one device in all modes.įor example, the TV volume will work in the cable and VCR modes. "SETUP" (2 blinks) 9 - 9 - 2, TV (you want to move TV) PRESS the DEVICE key you want to replace.Įxample: If you want the Aux key to be a TV key:.PRESS the DEVICE,(TV,VCR,CABLE,etc.),key you want moved.If the remote DOES NOT blink it means the number is 0. PRESS 3, carefully COUNT the number of blinks.PRESS 2, carefully COUNT the number of blinks.PRESS 1, carefully COUNT the number of blinks.PRESS the device,(TV,VCR,CABLE,etc.), button - RELEASE.When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes. ALTERNATE slowly between the POWER key and the DEVICE(TV,VCR,CABLE,etc.) button until your device turns off.(On VCR,LD,and CD players use PLAY instead of POWER).If you have tried all of the set-up codes for your brand of eqipment, or your brand is not listed, and you are still not able to get the unit to respond, try the following proceedure to search for your code. PRESS the POWER button to test the code.You should receive 2 quick flashes after entering your code.PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.PRESS the button for the device you want to program,(TV,VCR,CABLE,etc.), then RELEASE.
#How to program a urc remote how to#
How to Program your One For All® remote ( URC-5060, URC-5061, URC-5062, URC-5063, URC-5065 )Īfter getting the proper codes from your manual or Customer Service, use the following instructions to enter them into your remote. Everything under control with the official One For All homepage.